Dimensional Arts & HoloCom Inc.
HoloCom Inc. Technical Transfer Division is one of the best in the industry. Our Holographic Consultants provide
the latest in technical training in both basic and advanced techniques. Over 15 years of experience in the holographic industry makes
our consultants the most qualified in the world.
HoloCom Inc.' intensive six week training course insures a complete understanding of the technology. Training begins with
the setting up of the customer's facility. All training takes place on-location, which means the trainees learn on the same equipment
they will be operating, not in an already functioning laboratory. Completed training leaves the customer with a fully functioning facility in which all operations conform
to international standards involving patents, workplace safety, and environmental impact.
All necessary equipment including the Newport Isolation Table, the Liconix Embosser Series HeCd Laser, posts,
mounts, and optics is provided. Two levels of training are available, and include: Basic Techniques - Includes training in the production
of common diffraction patterns, 2D/3D, and 3D image originations. Included with training are complete laboratory setup and training in
troubleshooting common problems. Training in basic techniques provides the customer with an operational facility capable of producing quality rainbow
holograms for embossing.
Advanced Techniques - An extension of Basic Techniques training.
Advanced Techniques include multiple-exposures, full color imaging, achromatic, and complex diffraction patterns. Training in
advanced techniques requires either an operational laboratory facility or prior training in basic techniques. This training provides the
customer with the most up-to-date techniques available.
The customer need only provide a suitable building with adequate electricity, running water, a source of compressed nitrogen, clean
room facilities, and a deionizing water filtration system. If the reliability of electrical supply is in question, an uninterrupted power
supply may be required for the laser.
HoloCom Inc. offers three holographic stereogram cameras: a 16mm film type, based on a 16mm motion picture
camera; a 35mm film type, based on a 35mm motion picture camera; and a Computerized LCD System. All
three systems are capable of creating 3D animated holograms for embossing, and all three require a dedicated laser table.
The Computerized LCD System is based on the system designed by Chromagem Inc. Besides the ability to create 3D
animated holograms, the LCD system is capable of rendering computer graphics as a 3D hologram. This system is the current state of
the art in holographic stereogram origination technology.
The Dimensional Arts' image recombining system is the latest in mechanical recombining technology. It is designed for the
creation of diffraction patterns, ganging up small holographic images onto a single shim, and the building of wide web shims for
embossing. The recombining system is ideal for use with The Dimensional Arts Light Machine, and the creation of tiled
digital holographic patterns. The Dimensional Arts image recombining system is available as a stand alone unit, or in
combination with HoloCom Inc.' holographic origination and production equipment. The below specifications are for the 50"
x 24" active area recombining system. Custom machines are available for specific applications.
The press frame is of solid steel construction. The hydraulic circuit is 2 stage design for efficient operation.
- Press weight 6000# approximate
- Capacity: adjustable to 30 tons
- Image size: 14" to 2" square
- Ram Diameter: 5"
- System Pressure: 3000 max.
- Motor H.P. 2 230/460/3/60/1200
- Distance floor to working surface 45"
- Height at maximum dalite 70"
- Floor Space 48" L-R x 36" F-B
- 0 to 400 Heater assembly with digital display
- 24" x 50" Max. XY guide platform computer controlled system
At the conclusion of preparing a photo-resist master, the holographer is left with a laser etched, developed plate of glass that
is normally coated with a fragile positive reading resist. Encoded in its surface are the many fine grooves that produce the image. This coated glass cannot be used to emboss copies of the hologram into
plastic. Therefore, the electroforming process is used to perform the conversion from photo-resist master to metal master for the
subsequent production of copies in plastic or hot-stamping foil.
Electroforming, which has been utilized since the mid-19th Century, is basically an electroplating process in which the
substrate plated onto is separated from the plated portion. In other words, the metal master is grown upon the glass master and then
separated from it. The resultant metal master is then used to grow further metal masters or "shims", which are used to emboss into
plastic or hot-stamping foil.
Due to the excellent reproduction of even the most minute detail, electroforming is perfect for use in the holographic field and, indeed,
provides a crucial step in the embossing process.
- The standard electroforming system is provided with two types of plating tanks (both using the same equipment - only different
strengths of plating solution):
- An unstressed sulfamate tank used for growing thicker deposits on the master.
- A stressed tank used for growing the thinner stampers or "shims" used in actual production.
EQUIPMENT PER TANK:
- 12 volt 50 amp rectifier
- Recording amp hour meter
- Immersion quartz heater
- Immersion heater thermostat
- Filter chamber
- Cathode automatic shut off
- Titanium anode basket
- 55 gallon solution tank
Clean room (can be as small as 3 X 3 meters (10' X 10')) containing:
HoloCom Inc. offers polyester embossing machines from any of the major manufacturers which enables our clients to have
the in-house embossing capability which is so vital in today's manufacturing and security markets. Designed with both simplicity and
precision in mind, the machines are easy to operate and maintain. Most are fabricated to machine finishes of RMS 2 and manufactured
to tolerances of four decimal places. Interlocking safety panels on this equipment should satisfy standards world-wide.
- Electrical - 440 v. 3-phase, 50 amps per line
- Distilled or deionized water supply
- Water outlet drain
- Corrosion proof fan 250 CFM (425/hr) with external venting
The Model 2012, will produce hot-stamping embossings, polyester, and other select film embossing. It will reproduce mechanical
gratings, holography, and laser discs as well. The machine can be completely disassembled, serviced, and reassembled within 30
minutes and all electrical and pneumatic systems are easily and directly serviced in minutes. Machines are shipped ready-to-run.
The model EBN and EBA are identical machines with the model EBA being fitted with computerized pneumatic tension controllers for
unwinding and rewinding. These tension controllers automatically control unwind, rewind, and intermediate web tension by operating
magnetic particle brakes and clutches. This greatly reduces web stretching and allows the EBA to run a much lighter hot-stamping foil
than any other machine available. The tension controller also improves registration, reduce wrinkling, curling, and variation, thus
reducing waste during starts, stops, and splicing. These attributes are not necessary to all manufacturers and are therefore offered as an option.
Below are the technical specifications for the Model 2012:
- The Model 2012 is designed around a single embossing roller unlike the old style and less capable two-roller machine. Some significant reasons for the superior performance of the single-roller machine are:
- Ease of subsequent timing to rotary machines
- Perfect alignment panel to panel
- Increased shim life
- No mismatched panels due to uneven heat or pressure
- Better quality control as operator can view embossing roller during production.
Model 2012 Specifications
Maximum line speed (determined by material use)......................50 feet/min. approx.
Maximum web width.....................12 inches
Maximum unwind and rewind diameter....24 inches
Standard embossing area...............6 1/2" X 12"
Size and number of shims..............one 8 1/2" X embossed width desired
Estimated shim life (determined by many factors but generally on 2mil polyester.............................5,000 + feet
Repeatability - pattern to pattern....0.004" tolerance
Compressed air requirements...........minimum 80 psi of clean, dry air
Electrical supply requirements........20 amp, 120 volt, 50/60 cycle A/C
Machine length........................65 inches
Machine Height........................32 inches
Machine Width.........................25 inches
Machine shipping weight...............1500 lbs.(750 Kilos)
Machine shipping crate dimensions.....72" X 36" X 36"
All data subject to change to that in effect at time of shipment.
HoloCom Inc. offers several quality converting machines including the Newfoil Machine, and the Franklin Model
conversion including multi-image/color hot-stamping, over laminating, die cutting, kiss cutting and laddering off of scrap.
Standard features include:
Fully adjustable print and die heads:
Printing heads and cutting dies are adjustable for side to side, front to back, and rotational registration, simplifying "print to cut"
Precise adjustable print and die heads: While the Model 164 is printing, the handwheel may be adjusted for
precise front-to-back positioning of the web, thereby locating the imprint in the center of the label stock.
Electronic registration of web feed in .005" or .001" increments through precise stepping motor drive.
The web feed length is adjustable in .005" or .001" increments with digital thumbwheel switches that are easy to read
and reach even while the Model 164 is running. The one thousandth of an inch increments mode provides the finest resolution in the
industry. All without tools. Downtime is reduced because the operator can compensate for minor heat or usage induced changes in
the position of step and repeat plates.
Two motor driven roll leaf advances - Easily adjustable while machine is running.
Adjustable dwell and pressure for better control of imprint.
Variable electronic speed controller - from 1500 to 6500 cycles per hour.
Automatic tension control of supply and rewind.
Solid state temperature control with digital readout.
Simplified leveling adjustments for even impressions.
Easy access, front mounted electric foil rewinds.
Electronic predetermining counter with digital display counts down to zero and shuts off machine.
Model 164-68 Generation II Label Maker
Photo-electronic re-register device for multiple passes enables the addition of more colors and
variable information. Includes sensor for printed marks on top or bottom of web.
Three plate holding chases with tapped hole every inch. (Note: should not be used with 16 gauge plates).
Sheeter Stacker with provision for waste stripping prior to sheeting.
This unit is also programmable to cut labels in strips or "sets".
Computerized Web Guide uses a photo cell to sense the edge of the web and electronically.
compensates for web wander due to telescoped rolls, uneven slitting, etc. A precision stepping motor adjusts the entire supply roll in
the cross web direction when adjustment is necessary.
Digital Photo-Optic Registration System for hologram recognition and location in the FOIL FEED
SYSTEM (one of two foil feeds). Includes provision for blinding the photo optics to avoid optical noise on the holograms and digital
set re-registration distance.
Digital Photo-Optic Registration System for hologram recognition and location in the WEB FEED SYSTEM. Includes provision for
blinding the photo-optics to avoid optical noise on the holograms and digital set re-registration distance.
For more information contact: Ken Harris,
The Dimensional Arts Inc. HoloCom Inc.
401 Carver Rd..,
New Mexico, 88005
Phone: (505) 527-9183 Fax: (505) 527-9927
The Holography home page
Holocom's home page